Corrosion-resistant hot oil pump with the growth of the use of time, there will be inadequate pump oil, pump or even failure, mainly due to excessive wear and tear on the parts. Corrosion-resistant hot oil pump wear parts are the main shaft and bushings, passive gear center hole and shaft pin, pump housing cavity and gear, gear end face and pump cover. Lubricating oil pump wear of its main technical indicators fail to meet the requirements, it should disassemble, find out the location and extent of wear and tear, to take appropriate measures to be repaired.
Corrosion-resistant hot oil pump cavity cavity repair: After the pump cavity wear, the general use of lumen inlaid method to repair, is about to enlarging the inner cavity set with cast iron or steel bushings. After setting the sleeve, the cavity enamel to the required size, and wear out the end face of the liner to flush with the pump housing surface.
Corrosion-resistant hot oil pump drive shaft and bush wear, with the gap increases, will certainly affect the pump oil. In this case, you can repair the drive shaft or bushing method to restore its normal with the gap. If the drive shaft wear slightly, simply press the old bushing and put on the standard size bushing, with the gap can be restored to the allowable range. If the drive shaft and bushing wear serious and serious with excessive clearance, not only to replace the bushing, and the drive shaft also applies chrome or vibration welding method to increase its diameter, and then grinding to the standard size, recovery and bushing With the requirements. Repair of the oil pump housing Repair of the crack in the housing: Crack of the housing can be cast 508 nickel-copper welding electrode. Welds to be close and yuan stomatal, with the flatness of the pump cover with no more than 0.05 mm flatness. Repair of drive shaft bushing hole: The repair of drive shaft bushing hole on pump cover is the same as repair method of wear of drive shaft bushing hole of housing.
Corrosion-resistant hot oil pump work plane repair: If the pump cover wear a small working surface, manual grinding method can be used to eliminate wear marks, that is, put a little valve on the platform or thick glass sand, and then put the pump cover on the grinding, resistance Corrosion Hot pump with the use of time, there will be inadequate pump oil, pump or even failure, mainly due to excessive wear and tear on the parts. Corrosion-resistant hot oil pump wear parts are the main shaft and bushings, passive gear center hole and shaft pin, pump housing cavity and gear, gear end face and pump cover. Lubricating oil pump wear of its main technical indicators fail to meet the requirements, it should disassemble, find out the location and extent of wear and tear, to take appropriate measures to be repaired. Corrosion-resistant hot oil pump work plane repair: If the pump cover wear a small work surface, manual grinding method can be used to eliminate wear marks, that is, put a little valve platform sand or thick glass plate sand, and then the pump cover on the grinding until Wear marks removed, the work surface so smooth. When the pump cover working plane wear depth of more than 0.3 mm, should be taken after the first turning grinding method to repair. Follower shaft wear and tear to wear and tear to eliminate traces of reaming method, and then press the hole reaming the actual size of the preparation of the driven shaft.
Ion exchange resin is a crucial component used in glass fiber reinforced plastic pressure tanks to effectively remove both anions and cations present in water, ultimately softening the water.
The ion exchange resin works through a process known as ion exchange, where it replaces undesired ions in the water with more desirable ones. This resin is typically made up of small, porous beads that contain charged functional groups.
When water passes through the pressure tank containing the ion exchange resin, the resin beads attract and retain the unwanted anions and cations present in the water. These unwanted ions, such as calcium, magnesium, iron, and sulfates, are exchanged with more desirable ions like sodium or potassium.
The exchange process occurs as the water flows through the resin bed, allowing the resin beads to selectively trap the unwanted ions and release the desired ions. This effectively removes the minerals responsible for water hardness and replaces them with softer ions, resulting in softened water.
Softened water offers various benefits, including preventing scale buildup in pipes and appliances, improving the efficiency of water heaters, reducing soap scum and residue on surfaces, and providing better lathering and cleaning capabilities.
Ion Exchange Resin,Water Softener Resin,water deionization resin,mix bed resin,Resin
Hebei Chengda Water Technology Co.,Ltd. , https://www.arclionchengda.com