We can make with your samples and requirements!
Othe parts for tricycle also:
More motorcycle parts we can supply!
Â
| Motorcycle parts we can supply | |
| Engine parts | Cylinder head,Cylinder kit(Piston),Valve set,Arm rocker,Chain set(big sprocket,small sprocket,chain),Bearing,Clutch assy(clutch gear,clutch plates,clutch cover),Drive plate assy(weighing rollers,ace driven),Transmission assy( transmission belt,transmission,kick shaft,shift lever),Carburetor |
| Electrical parts | Stator,Stater motor,Ignition coil,Rectifier,CDI,Lock set(lock,cap) |
| Frame parts | Brake shoes,Brake disk,Barke pump assy,Fr&Re hub,Front hub iron,Rim,Brake pads,Rubber damper,Speedometer gear,Fuel cock,Speedometer,Turning light,Headlight,Tail light,Mirror,Fr&Re absorber,Horn,Cables(speedometer cable,throttle cable,brake cable),Battery,Battery |
| Body parts | Oil tank,Side cover,Front&Rear fender,Upper handie cover,Medification front cover,Front protector cover,Down cover,Side cover cap,Lnner box fairing |
| Motorcycle accessory | Handle grips,Nuts,Glooves |
More available parts for: Motorcycle,Atv,Pocket bike,Dirtbike etc
| HONDA | CG125 CG150 CG200 GY650(60 80 90 100 125 150) C70 C90 C100 C110 CUB90 WAVE100 WAVE110 WS110 WAVE125 CB125 CB150 SH125 SH150 TMX125 XRM125 WH125 |
| YAMAHA | 3KJ50 BWS MBK YB50 2JA JOG50 CRYPTON110 XC125 Y110 RX115 JY110 YBR125 MAJESTY250 CYGNUS X125 MIO NOUVO JUPITER-MX RXS115 |
| SUZUKI | GN125 GN150 AX100 GS125 AD50 AG50 HJ125 SMASH110 |
| KAWASAKI | BC175 KRISS BAJAJ-CT100 BAJAJ-CNG125 |
| ITALIKA | CS125, DS125, XS125/150, DS150, GS150, WS150, ST70, STRADA70, ST90, AT110, ARGENTA110, FT110/125/150, XT110, FORZA150 |
| BAJAJ | BOXER CT100, PULSAR135/150/180/200, DISCOVER125/135, PLATINO100/125 |
Powder coating is a dry finishing process that has become extremely popular. Powder coating is used on a wide array of products. More and more companies specify powder coatings for a high-quality, durable finish, allowing for maximized production, improved efficiencies, and simplified environmental compliance. Used as functional (protective) and decorative finishes, powder coatings are available in an almost limitless range of colors and textures, and technological advancements have resulted in excellent performance properties.
Advantages over other coating processes
1. Environment friendly. Powder coatings contain no solvents and release little or no amount of volatile organic compounds (VOC) into the atmosphere.
2. More thicker coatings without running or sagging than conventional liquid coatings.
3. Perfect color consistency. Powder coated items generally have fewer appearance differences than liquid coated items between horizontally coated surfaces and vertically coated surfaces.
4. A wide range of speciality effects are easily accomplished using powder coatings that would be impossible to achieve with other coating processes.
5. Curing time is significantly faster with powder coatings compared to liquid coatings especially when using ultraviolet cured powder coatings or advanced low bake thermosetting powders.
Powder Coating Process
The Powder coating process involves three basic steps: raw material preparation or the pre-treatment, the powder coating application and curing.
Powder Coating Substrate Considerations
Before applying the powder coating material, you must first consider the substrate material that you will be coating. It is very important to have a clear understanding of the true composition of the surface of the part.
ALUMINUM:
ALUMINUM CASTING
COLD/HOT ROLLED STEEL
CAST IRON
BRASS
COPPER
ZINC
STAINLESS STEEL
Powder Coating Properties:
|
Coating Properties |
|
|
Mechanical Properties |
Pencil hardness GB/T 6739-1996 H-2H |
|
Adhesion (cross-cut method) GB/T 9286-1998 Grade 0 |
|
|
Bending test GB/T 6742-1986 ≤ 2mm |
|
|
Impact test GB/T 1732-1993 ≥50kg.cm |
|
|
Cupping test GB/T 9753-1988 ≥7mm |
|
|
Corrosion Resistance |
Salt spray test GB/T 1771-1991 >500 hours, no change, crossion width at crossing ≤ 2mm |
|
Damp heat test GB/T 1740-1979 >1000 hours, mild loss of gloss |
|
|
Temperature resistance 100°C/48 hours, excellent gloss retention |
|
|
|
|
Powder Coating Colours
RALAL Range, Pantone Range, and other Natural Colour Systems (NCS)
If you have a Powder Coating Colour requirement that we do not stock we are usually able to source powders from the above ranges within 48 hours.
Powder Coating Gloss Level
Gloss is measured as a percentage.
1. Matt Powders are between 20% and 30% gloss.
2. Semi-gloss Powders are usually around 60-65% gloss.
3. Gloss Powders at least 80% and can be 85%.
Powder Coating finishes
1. Textured Powder Coating:
2. Ripple/Leatherette Powder Coating.
3. Hammerite Finish Powder Coating.
4. High Temperature Powder Coating.
5. Anti-Bacterial Powder Coating.
6. Clear or Tinted Powder Coatings.
Application Field
1. In automotive applications:
a) some primers used on bodywork have converted to powder. This has given improved coating quality and provided ecological advantages.
b) where a functional as well as a decorative finish is desirable powder coatings are being used increasingly eg.
i. - wheels,
ii. - bumper bars,
iii. - mirror frames,
iv. - oil filters,
v. - battery trays,
vi. - coil springs and
vii. - heads.
2. Appliances
a) Specially formulated, hard and scratch resistant powder coatings are replacing the energy-intensive porcelain finishes on washer tops and lids.
b) Powder coatings are being used on range housings, freezer cabinets, drier drums, and microwave oven cavities.
c) Outdoor furniture, farm and garden implements and garden tractors also are being finished with powder coating materials. - Interior fluorescent light reflectors are coated using a highly reflective, very thin powder coating.
d) Exterior lamp housings on highway and parking deck fixtures are coated with specially formulated powder which give ultra violet light protection and added corrosion protection
Powder Coating,Custom Powder Coating,Metal Powder Coating,Powder Coating Services
Suzhou FCE precision electronics Co., LTD , https://www.fcesz.com