Speed ​​probe CS-1-D-100-02-00,
CS-2-120-03, CS-3-100-04-02
The speed probe CS-1-D-100-02-00 adopts the principle of electromagnetic induction to realize speed measurement. A coil is wound around the front end of the sensor. Its outline drawing is shown in Fig. 1, and its installation is shown in Fig. 2. When the gear rotates, it passes through the sensor coil. The magnetic lines of force change, a periodic voltage is generated in the sensor coil, and the rotation speed of the gear can be measured by counting the voltage processing. The stainless steel sensor housing, the output signal is strong, anti-jamming performance, easy installation and use, can be used in the harsh environment of smoke, oil and gas, water and gas.
 1, output voltage: when the gear module is 4, the tooth 60, the material g3, the clearance is lmm
 1000 rev / min >5V (RMS)
 2000 rev/min >10V (effective value)
 3000 rev / min >15V (RMS)
 2, DC resistance:  130 ohms to 140 ohms (if the customer needs to use other resistance data, indicate when ordering)
3ã€Insulation resistance: >50MΩ at 500V DC
 4, working temperature: -20 °C ~ l20 °C
working principle
When used, a gear should be mounted on the shaft to be measured (the positive and the helical gears can be placed on the grooved disk), the sensor is mounted on the bracket, and the gap between the sensor and the gear tooth tip is adjusted to about 1 mm.
When the shaft rotates, it drives the gear to rotate. According to the principle of electromagnetic induction, a voltage pulse signal is generated at both ends of the sensor's internal coil. When the shaft rotates for one revolution, Z (number of teeth) voltage pulses are generated. This signal is input to the JX5031 tachometer. Set the number of teeth in the tachometer, the tachometer can reflect the rotation speed of the shaft will be converted into electrical signals for the counter to count the count, non-contact can measure a variety of magnetic materials such as: gear, impeller, with holes (or slots, Screw) Speed ​​and linear speed of the disc (or shaft).
The sensor has the advantages of small size, strong and reliable, long life, no need of power supply, etc., and can be matched with general speed instruments.
CS-2-120-03 Speed ​​probe When the metal tooth passes through the Hall sensor front end, it causes a magnetic field change. The Hall element detects a magnetic field change and converts it into an alternating current signal. The built-in circuit of the sensor amplifies and reshapes the signal. , Output a good rectangular pulse signal, measuring a wider frequency range, the output signal is more accurate and stable, easy to install, oil and waterproof, has been widely used in the field of electric power, automotive, aviation, textile, petrochemical and other speed measurement
2 Technical parameters
2.1 Operating Voltage: DC5~24V
2.2 Measurement Range: 0~20KHz
2.3 Speed ​​measuring gear form: Modulus 2 to 4 (involute gear)
2.4 Output signal: square wave, whose peak-to-peak value is equal to the working supply voltage amplitude, independent of the rotation speed, the maximum output current is 20mA.
2.5 Operating Temperature: -30 to +150°C
CS-2-120-03, CS-3-100-04-02
The speed probe CS-1-D-100-02-00 adopts the principle of electromagnetic induction to realize speed measurement. A coil is wound around the front end of the sensor. Its outline drawing is shown in Fig. 1, and its installation is shown in Fig. 2. When the gear rotates, it passes through the sensor coil. The magnetic lines of force change, a periodic voltage is generated in the sensor coil, and the rotation speed of the gear can be measured by counting the voltage processing. The stainless steel sensor housing, the output signal is strong, anti-jamming performance, easy installation and use, can be used in the harsh environment of smoke, oil and gas, water and gas.
 1, output voltage: when the gear module is 4, the tooth 60, the material g3, the clearance is lmm
 1000 rev / min >5V (RMS)
 2000 rev/min >10V (effective value)
 3000 rev / min >15V (RMS)
 2, DC resistance:  130 ohms to 140 ohms (if the customer needs to use other resistance data, indicate when ordering)
3ã€Insulation resistance: >50MΩ at 500V DC
 4, working temperature: -20 °C ~ l20 °C
working principle
When used, a gear should be mounted on the shaft to be measured (the positive and the helical gears can be placed on the grooved disk), the sensor is mounted on the bracket, and the gap between the sensor and the gear tooth tip is adjusted to about 1 mm.
When the shaft rotates, it drives the gear to rotate. According to the principle of electromagnetic induction, a voltage pulse signal is generated at both ends of the sensor's internal coil. When the shaft rotates for one revolution, Z (number of teeth) voltage pulses are generated. This signal is input to the JX5031 tachometer. Set the number of teeth in the tachometer, the tachometer can reflect the rotation speed of the shaft will be converted into electrical signals for the counter to count the count, non-contact can measure a variety of magnetic materials such as: gear, impeller, with holes (or slots, Screw) Speed ​​and linear speed of the disc (or shaft).
The sensor has the advantages of small size, strong and reliable, long life, no need of power supply, etc., and can be matched with general speed instruments.
CS-2-120-03 Speed ​​probe When the metal tooth passes through the Hall sensor front end, it causes a magnetic field change. The Hall element detects a magnetic field change and converts it into an alternating current signal. The built-in circuit of the sensor amplifies and reshapes the signal. , Output a good rectangular pulse signal, measuring a wider frequency range, the output signal is more accurate and stable, easy to install, oil and waterproof, has been widely used in the field of electric power, automotive, aviation, textile, petrochemical and other speed measurement
2 Technical parameters
2.1 Operating Voltage: DC5~24V
2.2 Measurement Range: 0~20KHz
2.3 Speed ​​measuring gear form: Modulus 2 to 4 (involute gear)
2.4 Output signal: square wave, whose peak-to-peak value is equal to the working supply voltage amplitude, independent of the rotation speed, the maximum output current is 20mA.
2.5 Operating Temperature: -30 to +150°C
Free Nail Adhesive,Nail Free Construction Adhesive,Nail Free Fixing Adhesives,Adhesive Sandpaper Steel Nail File
Foshan Feiyi Adhesive Technology Co., Ltd. , https://www.fsnh-feiyi.com