Plants, as living individuals, require different amounts of nutrients for water and nutrients at various stages of their growth. However, in the past, conventional agricultural production made it difficult for people to find instruments such as plant nitrogen analyzers. Communication channels are established between plants and plants, so it is difficult for people to understand the real needs of plants. This also causes problems such as excessive application of nutrients, and affects the quality of agricultural production to varying degrees, and with the science The development of technology and the progress of mankind, especially the application of plant nitrogen analyzers, provide important technical support for precision agriculture, and thus have the conditions to further enhance the plant's production potential.
Nitrogen can be said to be an important indicator of plant growth, and nitrogen is also a major element of protein composition. It has an important influence on the entire growth and development of plants. Plants with insufficient nitrogen content have poor growth conditions, and crop dwarf fruits are not full and their nutrient content is not high. However, if the nitrogen content is too high, causing the plants to grow madly, not only the normal reproduction of the plant is destroyed, but also the lodging phenomenon is likely to occur during the growth process, affecting the plant quality and yield. It can be seen that applying too little or too much nitrogen fertilizer will affect the growth and production yield and quality of plants in varying degrees. Therefore, only plants with balanced nutrients and healthy growth can be potential plants.
The application of plant nitrogen analyzer can make the modern farmers' fertilization operation no longer blind. The plant nitrogen analyzer can determine the nitrogen content of plants, understand the true nitrogen conditions of plants, and make the plant grow in long-term. Monitoring the scope of detection, so that if the early discovery of nitrogen is not enough, can increase nutrient supply to the plant; otherwise, it can prevent excessive application of nutrients. This can accurately guide the application of nitrogen fertilizer and other fertilizers, providing the basis for the high yield and quality of crops.
Tungsten carbide roller has characteristics of good wear resistance, high temperature red hardness, thermal fatigue resistance and thermal conductivity and high strength , have been widely used in high-speed wire rod, bar, rebar, seamless steel tubes, etc. Domestic production of tungsten carbide roller materials mostly WC- Co, WC- Co- Ni- Cr two series, and the content of Co, Co- Ni - Cr is in the range of 6wt% ~ 30wt%. From the use of perspective, tungsten carbide rollers has good mechanical properties, its flexural strength up to 2200 MPa or more, shock toughness up (4 ~ 6) × 10^6 J/ m^2, Rockwell hardness (HRA) is up to 78 to 90, widely in the high-speed wire rod rolling process, which is much higher than single-slot chilled cast steel or high speed steel rolls.Tungsten carbide is made of Tungsten Carbide Powder and binder phase (such as drilling, nickel, etc.), and then pressing and sintering, regardless of the conditions under cold rolled or hot rolled has excellent wear resistance, tungsten carbide rollers has been widely used in pre-finishing mill and finishing of high-speed wire rod currently. On the performance of tungsten carbide roller in hot-rolling wire rod , the material must meet the following requirements:
1. Sufficient anti-fracture strength;
2. Good abrasion resistance;
3. The smooth surface finish;
4. Excellent corrosion resistance, thermal fatigue, thermal cracking performance.
Tungsten carbide roller rings can working in bad conditions , small profile rolling (especially rebar rolling) process conditions is harsher than the high-speed wire rod, and therefore corresponds to the profile rolling ,tungsten carbide rollers recommend using high binder phase carbide.
Tungsten carbide roller material design
Pre-finishing all vehicles roller should ensure its high toughness, strength, rigidity and thermal conductivity, followed before considering its wear resistance. When designing each vehicles roller, pre-finishing materials should choose carbide grades of Co, Co- Ni- Cr binder content is high (greater than or equal to 25wt%) , requiring an average WC grain size of coarse (5μm ~ 6μm), to obtain a higher shock toughness, proper strength and hardness. For the finishing of the roller movements, particularly the last two rollers of the finish rolling, which suffered load is small, and high relative velocity of the material to be pressed (80 m / min ~ 120 m / min). In this case, the wear resistance of the roller to be the most important requirements, and must ensure the strength , timpact toughness and hardness of a reasonable match, so the binder of Co / Ni content ratio and the average grain WC control of particle size and other factors must have greater control in front of different pre-finishing rolling roll.
Tungsten carbide roller category
According to the structure of tungsten carbide rollers, it can be divided into solid tungsten carbide roller and composite tungsten carbide roller. Solid tungsten carbide rollers have been widely used in pre-finishing and finishing stands high speed wire rod mill (including fixed reducing the rack, pinch roller rack). Composite tungsten carbide roller is made of cemented carbide and other materials, and it can be divided into tungsten carbide composite roll rings and solid tungsten carbide Composite Roller. Tungsten carbide composite roll rings mounted on the roller shaft; solid tungsten carbide composite roller will be directly cast in the roll axis to form a whole, a large load is applied to the rolling mill.
Tungsten carbide roller production process control
Tungsten carbide rollers produced by powder metallurgy method, the key to its process control is the chemical composition of the material and the mixture was prepared, pressed molding, sintering and deep processing and other preparation process parameters.
1. Preparation of starting material (WC focus quality): As the WC raw material and quality control of the use of different levels of quality may fluctuate, resulting in adverse effects on microstructure.
2. Preparation of the mixture: Mixture preparation is the key to the production process of the roller, the roller of failure modes - trachoma, mainly generated by this procedure.
3. Pressing: roller pressing is an important process of the roller mill.
4. Sintering: roller sintering is to determine the final quality of the roller production processes, use of advanced low-pressure sintering technology, HIP sintering technology can greatly improve the performance of roller.
5. Deep processing: deep processing rollers have a greater impact on the quality and accuracy of the roller surface.
Carbide Roller,Carbide Ring,Mill of Rolling Line,Steel Wire Rod,Mill Rolling Finish Stand,Mill Roller Groove Type
Luoyang Golden Egret Geotools Co., Ltd , https://www.xtchvaf.com