- Model NO.: 6/4E-MA
- Max.Capacity: 300-400 L/min
- Impeller Number: Single-Stage Pump
- Influent Type of Impeller: Single Suction Pump
- Pump Casing Combined: Horizontal Split Pumps
- Impeller: Open
- Pump Size: 4"
- Pump Shaft Seal: Gland Packed, Centrifugal Seal, Mechanical Seal
- Transport Package: Plywood Case
- Origin: Shijiazhuang, China
- Max.Head: 50-80m
- Driving Type: Motor
- Working Pressure: Low Pressure Pump
- Position of Pump Shaft: Horizontal Pump
- Mounting Height: Suction Centrifugal
- Usage: Pump, Pumps, Condensate Pump, Ash Pumps, Circulating Pump
- Pump Character: Handling Abrasive Slurry
- Trademark: MUYUAN
- Specification: CE, SGS
- HS Code: 841370
Â
MA series slurry pumps are the most comprehensive range of centrifugal slurry pumps for use in mining, chemical and general industry applications. The horizontal slurry pumps are designed for heavy duty applications such as mill discharge, power sector and tailings as well as specialty applications, which are used for continuous pumping of high abrasive, high density slurry.
Notation:
Â
Product Features:
-Wear resistant metal or rubber wet end parts, long service life
-Wide options for impeller
-Various types of pump seals to suit different working condition
-Grease or oil lubrication
-Discharge branch can be positioned at intervals of 45 degree
-Can be installed in multistage series
-Easy to maintain
Pump Structure:
Â
Technical Parameters:
Size: 25 mm to 450 mm
Capacity: up to 5000 m3/hr
Maximum Heads: up to 75 m
Selection Chart:
| Pump Type | Pump Model | Size | Flow | Head | Application | Feature |
| MA/MAR Heavy Duty Slurry Pump |
1.5/1B-MA | 1"-18" | 4-5400 m3/h | 5-75m | -Ball Mill Discharge | -Wear resistant metal or    rubber wet end parts,    long service life |
| 2/1.5B-MA | -SAG Mill Discharge | |||||
| 3/2C-MA | -Rod Mill Discharge | |||||
| 4/3C-MA | -Coal Washing | -Wide options for impeller | ||||
| 4/3D-MA | -Coarse Sand | -Various types of pump seals to   suit different working condition |
||||
| 6/4D-MA | -Coarse Tailing | |||||
| 6/4E-MA | -FGD | -Grease or oil lubrication | ||||
| 8/6E-MA | -Fine Tailing | -Discharge branch can be   positioned at intervals of 45 degree |
||||
| 8/6F-MA | -Flotation | |||||
| 10/8F-MA | -Heavy Media | -Can be installed in multistage series | ||||
| 10/8ST-MA | -Mineral Processing | -Easy to maintain | ||||
| 10/8G-MA | -Mineral Concentrate | Â | ||||
| 12/10F-MA | -Pulp and Paper | Â | ||||
| 12/10ST-MA | -Process Chemical | Â | ||||
| 12/10G-MA | -Oil Sand | Â | ||||
| 14/12F-MA | -Mineral Sand | Â | ||||
| 14/12ST-MA | -Pulp and Paper | Â | ||||
| 14/10G-MA | Â | Â | ||||
| 16/14TU-MA | Â | Â | ||||
| 20/18TU-MA | Â | Â |
Continuous casting slabs or primary rolling slabs are used as raw materials, heated by a stepping furnace, and dephosphorized by high-pressure water, and then enter the roughing mill. The rough rolling material is cut through the head, tail, and then into the finishing mill, and computer-controlled rolling is carried out. After the final rolling, it will go through laminar cooling (computer-controlled cooling rate) and take-up by the coiler to become a straight hair coil. The head and tail of straight hair curls tend to be tongue-shaped and fish-tailed, with poor thickness and width accuracy, and often have wavy, folded, tower-shaped and other defects on the edges. The coil is heavier and the inner diameter of the steel coil is 760mm. (Generally used in the pipe-making industry.) After straightening the hair through the cutting head, tail cutting, trimming and multi-pass straightening and smoothing finishing lines, and then cutting or re-rolling, it becomes: hot rolling Steel plates, flat hot rolled steel coils, slitting tapes and other products. If the hot-rolled finishing coil is pickled to remove scale and coated with oil, it will become a hot-rolled pickled coil.
Carbon Steel Coil,Cold Rolled Steel Coil,Cold Rolled Steel Coils,Hard Cold Rolled Steel Coil
Shandong Guanzhou Iron and Steel Group Co., Ltd. , https://www.guanzhouiron.com